View ST183C_1317276.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Previous Datasheet
Index
Next Data Sheet
DISCRETE POWER DIODES and THYRISTORS
DATA BOOK
D-520
To Order
Previous Datasheet
Index
Next Data Sheet
Bulletin I25178/A
ST183C..C SERIES
INVERTER GRADE THYRISTORS Features
Metal case with ceramic insulator International standard case TO-200AB (A-PUK) All diffused design Center amplifying gate Guaranteed high dV/dt Guaranteed high dI/dt High surge current capability Low thermal impedance High speed performance
Hockey Puk Version
370A
Typical Applications
Inverters Choppers Induction heating All types of force-commutated converters
case style TO-200AB (A-PUK)
Major Ratings and Characteristics
Parameters
IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I 2t @ 50Hz @ 60Hz V DRM /V RRM tq range TJ
ST183C..C
370 55 690 25 4900 5130 120 110 400 to 800 10 to 20 - 40 to 125
Units
A C A C A A KA2s KA2s V s
C
D-521
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code V DRM /V RRM , maximum repetitive peak voltage V
04 ST183C..C 08 800 900 400
VRSM , maximum non-repetitive peak voltage V
500
I DRM /I RRM max.
@ TJ = TJ max.
mA
40
Current Carrying Capability
Frequency
180 el 50Hz 400Hz 1000Hz 2500Hz Recovery voltage Vr Voltage before turn-on Vd Rise of on-state current di/dt Heatsink temperature Equivalent values for RC circuit 770 730 600 350 50 V DRM 50 40
o
ITM 180 el 660 600 490 270 50 50 55 1220 1270 1210 860 50 V DRM 40
o
ITM 100s 1160 1090 1040 730 50 55 5450 2760 1600 800 50 V DRM 40
ITM
Units
4960 2420 1370 680 50 55 V A/s C A
47 / 0.22F
47 / 0.22F
47 / 0.22F
On-state Conduction
Parameter
I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one half cycle, non-repetitive surge current
ST183C..C
370 (130) 55 (85) 690 4900 5130 4120 4310
Units
A C
Conditions
180 conduction, half sine wave double side (single side) cooled DC@ 25C heatsink temperature double side cooled t = 10ms No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max
A
t = 8.3ms t = 10ms t = 8.3ms t = 10ms t = 8.3ms
It
2
Maximum I t for fusing
2
120 110 85 78 KA2s
t = 10ms t = 8.3ms
I 2 t
Maximum I2t for fusing
1200
KA2s
t = 0.1 to 10ms, no voltage reapplied
D-522
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Fig. 3 - Current Ratings Characteristics
Fig. 4 - Current Ratings Characteristics
Fig. 5 - On-state Power Loss Characteristics
Fig. 6 - On-state Power Loss Characteristics
Fig. 7 - Maximum Non-repetitive Surge Current Single and Double Side Cooled
Fig. 8 - Maximum Non-repetitive Surge Current Single and Double Side Cooled
D-526
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Fig. 9 - On-state Voltage Drop Characteristics
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
Fig. 11 - Reverse Recovered Charge Characteristics
Fig. 12 - Reverse Recovery Current Characteristics
Fig. 13 - Frequency Characteristics
D-527
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Fig. 14 - Frequency Characteristics
Fig. 15 - Frequency Characteristics
Fig. 16 - Maximum On-state Energy Power Loss Characteristics
D-528
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Fig. 17 - Gate Characteristics
D-529
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
On-state Conduction
Parameter
V TM Max. peak on-state voltage voltage V T(TO)2 High level value of threshold voltage r
t1
ST183C..C Units
1.80 1.40 1.45 0.67 m 0.58 600 1000 mA V
Conditions
ITM= 600A, TJ = TJ max, t = 10ms sine wave pulse
p
V T(TO)1 Low level value of threshold
(16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max. T J = 25C, I T > 30A T J = 25C, V A= 12V, Ra = 6, I G = 1A
Low level value of forward slope resistance
r
t2
High level value of forward slope resistance Maximum holding current Typical latching current
IH IL
Switching
Parameter
di/dt Max. non-repetitive rate of rise of turned-on current t
d
ST183C..C Units
1000 1.1 Min 10 Max 20 s A/s
Conditions
TJ = TJ max, VDRM = rated VDRM ITM = 2 x di/dt TJ= 25C, VDM = rated VDRM, ITM = 50A DC, t = 1s
p
Typical delay time
Resistive load, Gate pulse: 10V, 5 source TJ = TJ max, ITM = 300A, commutating di/dt = 20A/s VR = 50V, t = 500s, dv/dt: see table in device code
p
t
q
Max. turn-off time
Blocking
Parameter
dv/dt IRRM IDRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current
ST183C..C Units
500 40 V/s mA
Conditions
TJ = TJ max. linear to 80% VDRM, higher value available on request TJ = TJ max, rated V DRM/V RRM applied
Triggering
Parameter
PGM Maximum peak gate power
ST183C..C Units
60 10 10 20 V W A
Conditions
TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t 5ms
p
PG(AV) Maximum average gate power IGM +VGM -VGM IGT VGT IGD VGD Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage Max. DC gate current required to trigger Max. DC gate voltage required to trigger Max. DC gate current not to trigger Max. DC gate voltage not to trigger
TJ = TJ max, t 5ms
p
5 200 3 20 0.25 mA TJ = 25C, VA = 12V, Ra = 6 V mA V TJ = TJ max, rated VDRM applied
D-523
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Thermal and Mechanical Specification
Parameter
TJ T
stg
ST183C..C
-40 to 125 -40 to 150 0.17 0.08 0.033 0.017 4900 (500)
Units
C
Conditions
Max. operating temperature range Max. storage temperature range
RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, case to heatsink F Mounting force, 10%
DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled N (Kg) g See Outline Table
K/W
wt
Approximate weight Case style
50 TO - 200AB (A-PUK)
RthJ-hs Conduction
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
Conduction angle
180 120 90 60 30
Sinusoidal conduction
Single Side Double Side 0.015 0.018 0.024 0.035 0.060 0.016 0.019 0.024 0.035 0.060
Rectangular conduction
Single Side Double Side 0.011 0.019 0.026 0.036 0.060 0.011 0.019 0.026 0.037 0.061
Units
Conditions
K/W
TJ = TJ max.
Ordering Information Table
Device Code
ST
1 1 - Thyristor 2 - Essential part number 3 - 3 = Fast turn off 4 - C = Ceramic Puk
18
2
3
3
C
4
08
5
C
6
H
7
K
8
1
9 10
5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - C = Puk Case TO-200AB (A-PUK) 7 - Reapplied dv/dt code (for tq test condition) 8 - tq code dv/dt - tq combinations available
dv/dt (V/s) 20 CN CM CL CP CK 50 DN DM DL DP DK 100 EN EM EL EP EK 200 FN* FM FL* FP FK 400 HN HM HL HP HK
10 12 9 - 0 = Eyelet term. (Gate and Aux. Cathode Unsoldered Leads) t (s) 15 q 18 1 = Fast-on term. (Gate and Aux. Cathode Unsoldered Leads) 20
2 = Eyelet term. (Gate and Aux. Cathode Soldered Leads)
3 = Fast-on term. (Gate and Aux. Cathode Soldered Leads) 10 - Critical dv/dt: None = 500V/sec (Standard value) L = 1000V/sec (Special selection)
*Standard part number.
All other types available only on request.
D-524
To Order
Previous Datasheet
Index
Next Data Sheet
ST183C..C Series
Outline Table
ANODE TO GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. 19 (0.75) DIA. MAX. 0.3 (0.01) MIN.
13.7 / 14.4 (0.54 / 0.57) 0.3 (0.01) MIN. 19 (0.75) DIA. MAX. 38 (1.50) DIA MAX. GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE
Case Style TO-200AB (A-PUK)
All dimensions in millimeters (inches)
2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19)
25 5
42 (1.65) MAX. 28 (1.10)
Fig. 1 - Current Ratings Characteristics
Fig. 2 - Current Ratings Characteristics
D-525
To Order

▲Up To Search▲

Price & Availability of ST183C

	To Download ST183C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .